0.3PitchFPC连接器产品规范

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2 0．3Pitch 1.0H ZIF Connector Item 1 Update List: Update Description Rev. Issued Date New Edit 2010/10/2 Revisor Yzxhello Prepared By：Yzxhello Rechecked By： Approved By：

Product Name: FPC

1 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2 1. SCOPE This specification covers the FPC0310 Series Connector.

2. ORDERING INFORMATION PART NO.：

XX XX - xx XX - 0.3 X X X

1 2 3 4 5 6 7

1 FPC Connector 2 3 4 5 6 Plating Gold flash 7 Packaging R :Tape Reel

3. CONNECTOR DIMENSIONS

See attached drawings.

4. MATERIAL

Housing : LCP Color : Black. Flammability Rating (UL94V-0) Actuator LCP Color : Black. Flammability Rating (UL94V-0) Contact : Phosphor Bronze Leg : Phosphor Bronze Contact Plating See Ordering Information Leg Plating: Tin over Nickel 5. ACCOMMODATED P.C.B. LAYOUT See attached drawings.

Product Name: FPC

2 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification ITEM STANDARD 30V AC 0.2A DC Issued Date2010-10-2 6. RATING. Operating Voltage (Max.) Current Rating (Max.) Operating Temperature Operating Humidity range Storage temperature range Storage Humidity range -55°C ~ +85°C (Including terminal temperature rise) Relative humidity 90%Max -10°C ~ +50°C Relative humidity 90%Max. 7. PERFORMANCE 项目 ITEM 测试条件 TEST CONDITION 电气特性 (ELECTRICAL PERFORMANCE) 将样品与适合之 FPC 连接，测试电压 20mV，限电流 10mA 下进行阻抗测试。 规格 REQUIRMENT 接触阻抗 Contact Resistance (JIS C5402 5.4) Mate applicable FPC and measure by dry circuit, 20mV Max, 10mA. (JIS C5402 5.4) 40 mΩ 以下. 40 mΩ Max. 绝缘阻抗 Insulation Resistance 将样品与适合之 FPC 连接，提供相邻端子间测试电压 500V DC 进行绝缘阻抗测试。 (JIS C5402 5.2 / MIL-STD-202 Method 302) Mate applicable FPC and apply 500V DC between adjacent terminal or ground. (JIS C5402 5.2 / MIL-STD-202 Method 302) 50 MΩ 以上. 50 MΩ Min. 耐电压 Dielectric Strength 将样品与适合之 FPC 连接，相邻端子间需可承受 250V AC(rms) 1 分钟。 目视外观无任何损坏异状 (JIS C5402 5.1 / MIL-STD-202 Method 301) Mate applicable FPC, apply 250V AC(rms) for 1 minute between adjacent terminal or ground. (JIS C5402 5.1 / MIL-STD-202 Method 301) No Breakdown 机械特性 (MECHANICAL PERFORMANCE) FPC 保持力 FPC Retention Force 将盖子盖上，与 FPC 连接，以操作速度每分钟位移 25±3mm 进行 FPC 保持力测试。 Pos. x 0.15N 以上 Insert the actuator, pull the FPC at a rate of 25±3mm Pos. x 0.15N Min. per minute. 端子与 Housing 组装后，以操作速度每分钟位移 25±3mm 将端子拔出 Housing，进行端子保持力测试。 Pos. x 0.08Kgf {0.8N} 以上 Apply axial pull out force at the rate of 25±3 Pos. x 0.08Kgf {0.8N} Min. mm/minute on the terminal assembled in the housing. 3 of 10

端子保持力 Terminal Retention Force Product Name: FPC

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification 测试条件 TEST CONDITION 将盖子与 FPC 反复连接，以每分钟小于 10 cycles 连续操作 20 次。 Insert and withdraw actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. 量测通过 FPC 最大容许电流时，样品接触点之温升。 (UL498) Mate applicable FPC and measure the temperature rise of contact when the maximum AC rated current is passed. (UL498) 通过 DC 电流 1mA，位移相对距离 1.5mm，振动周期10∼55∼10 Hz 在 1 分钟内，持续 2 小时，方向在 X,Y,Z轴做测试。 (MIL-STD-202 Method 201) Mate connectors and subject to the following vibration conditions, for period of 2 hours in each of 3 mutually perpendicular axes, passing DC 1mA during the test. Amplitude : 1.5mm P-P Frequency : 10∼55∼10 Hz in 1 minute. Duration : 2 hours in each of X,Y,Z axes. (MIL-STD-202 Method 201) 将样品与适合之 FPC 连接，通过 DC 1 mA 测试条件， 连续测试 3 次。在 X、Y、Z 3 轴 6 个2 垂直方向施予重力加速度.490m/s{50G} 冲击。 (JIS C0041/MIL-STD-202 Method 213) Mate applicable FPC and subject to the following shock conditions. 3 times of shocks shall be applied for each 6 directions along 3 mutually perpendicular axes, passing DC 1 mA current during the test. (JIS C0021 / MIL-STD-202 Method 108) 接触阻抗 Contact Issued Date2010-10-2规格 REQUIRMENT 项目 ITEM 盖子往返操作测试 Repeated Actuator Insertion/ Withdrawal 温升 Temperature Rise 60 mΩ 以下. 60 mΩ Max. Resistance 温升 Temperature rise 30°C 以下. 30°C Max. 耐振性 Vibration 外观 Appearance 接触阻抗 Contact Resistance 瞬间断电 Discontinuity 目视外观无任何 损坏异状 No Damage 60 mΩ 以下. 60 mΩ Max. 1 μsec 以下. 1 μsec Max. 目视外观无任何 损坏异状 No Damage 耐冲击性 Shock 外观 Appearance 接触阻抗 Contact Resistance 瞬间断电 Discontinuity 60 mΩ 以下. 60 mΩ Max. 1 μsec 以下. 1 μsec Max. 目视外观无任何 损坏异状 No Damage 耐热性 Heat Resistance 耐寒性 Cold Resistance 外观 将样品与适合之 FPC 连接，置于环境温度 85±2°C Appearance 测试时间 96 小时，再置放于室温下 1∼2 小 时。 Mate applicable FPC and expose to 85±2°C for 96 hours. Upon completion of the exposure period, the test specimens shall 接触阻抗 be conditioned at ambient room conditions for 1 Contact to 2 hours, after which the specified Resistance measurements shall be performed. (JIS C0021 / MIL-STD-202 Method 108) 外观 将样品与适合之 FPC 连接，置于环境温度-40±2°C， 测试时间 96 小时，再置放于室温下 1Appearance ∼2 小时。 (JIS C0020) Mate applicable FPC and expose to -40±2°C for 接触阻抗 96 hours. Upon completion of the exposure Contact period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, Resistance after which the specified measurements shall be performed.(JIS C0020) 60 mΩ 以下. 60 mΩ Max. 目视外观无任何 损坏异状 No Damage 60 mΩ 以下. 60 mΩ Max. Product Name: FPC

4 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification 测试条件 TEST CONDITION 将样品与适合之 FPC 连接，置于环境温度 60±2°C， 相对湿度 90∼95%，测试时间 96 小时，再置放于室温 下 1∼2 小时。 (JIS C0022 / MIL-STD-202 Method 103) Mate applicable FPC and expose to 60 ± 2°C, relative humidity 90 to 95% for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C0022 / MIL-STD-202 Method 103) 将样品与适合之 FPC 连接，承受 5 cycles 冷热冲击后， 置放于室温下 1∼2 小时。 1 cycle time 如下 a) -55±3°C 30 分钟 b) +85±3°C 30 分钟 (JIS C0025) Mate applicable FPC and subject to the following conditions for 5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. Issued Date2010-10-2规格 REQUIRMENT 项目 ITEM 耐湿性 Humidity 外观 Appearance 接触阻抗 Contact Resistance 耐电压 Dielectric Strength 目视外观无任何 损坏异状 No Damage 60 mΩ 以下. 60 mΩ Max. 需能符合耐电压 测试 No Breakdown 冷热冲击 Temperature Cycling 绝缘阻抗 20 MΩ 以上. 20 MΩ Min. Insulation Resistance 外观 目视外观无Appearance 任何 损坏异状 No Damage 接触阻抗 Contact Resistance 60 mΩ 以下. 60 mΩ Max. 盐水喷雾 Salt Spray 1 cycle a) -55±3°C 30minutes b) +85±3°C 30minutes (Transit time shall be with in 3 minutes) (JIS C0025) 外观 将样品与适合之 FPC 连接，使用 5±1%浓度盐水，测试温度 35±2°C，测试时间 48±4 小时,后于室温下Appearance 使用清水 冲洗后再干燥。 (JIS C0023 / MIL-STD-202 Method 101) Mate applicable FPC and expose to the following salt mist conditions. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified 接触阻抗 NaCl solution Contact Concentration : 5 ± 1% Resistance Spray time : 48 ± 4 hours Ambient temperature : 35 ± 2°C (JIS C0023 / MIL-STD-202 Method 101) 目视外观无任何 损坏异状 60 mΩ 以下. 60 mΩ Max. Product Name: FPC

5 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification 测试条件 TEST CONDITION Issued Date2010-10-2规格 REQUIRMENT 项目 ITEM 二氧化硫(气体) SO2 Gas 氨(气体) NH3 Gas 焊锡性 Solderability 外观 将样品与适合之 FPC 连接，将其置放于 50±5 ppm 浓 度二氧化硫气体中，测试温度 40±2°C，测试时间 24 Appearance 小 时。 Mate applicable FPC and expose them to the 接触阻抗 following SO2 gas atmosphere. Contact Temperature 40 ± 2°C Resistance Gas Density 50 ± 5 ppm Duration 24 hours 外观 暴露来自浓度 28%阿摩尼亚之蒸发气体 NH3 中，测试 Appearance 时间 40 分钟。 40 minutes exposure to NH3 gas evaporating from 接触阻抗 28% Ammonia solution. Contact Resistance 润湿性 锡温 245±5°C，将导电端子浸入锡炉液面至 Housing距离锡面 0.1mm 位置，焊锡时间 3±0.5 秒。 Solder Tip of solder tails and fitting nails into the Wetting molten solder (held at 245±5°C) up to 0.1mm from the bottom of the housing for 3±0.5 seconds. 目视外观无任何 损坏异状 No Damage 60 mΩ 以下. 60 mΩ Max. 目视外观无任何 损坏异状 No Damage 60 mΩ 以下. 60 mΩ Max. 润湿面积 75%以 上，并不得有漏焊 针孔现象 75% of immersed area must show no voids, pin holes. 焊锡耐热性 使用红外线回焊时请参考第 8 点 Resistance to Soldering When reflowing…Refer to paragraph 8. Heat 外观 Appearance 目视外观无任何 损坏异状 No Damage 使用烙铁手焊时须可符合下述焊锡条件 Soldering iron method 0.2mm from terminal tip and fitting nail tip. Soldering time: 5 seconds Max. Solder temperature : 370~400°C Product Name: FPC

6 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2 8. INFRARED REFLOW CONDITION

250°C MAX.(Peak Temp.)3Sec. or less

230°C MIN. / 20～40Sec. °C

230

200

150 100 50

0

Start 60 Sec. 60～90 Sec.

30 Sec.

Time(sec.)

NOTE: Please check the re-flow soldering condition by your own devices beforehand .

Because the condition changes by the soldering devices, p.c. boards, and so on.

9. TAPE AND REEL PACKAGE SPECIFICATION

9-1.Tape and Reel Dimensions：See attached drawings. 9-2. Specification. No. of Contacts 13~25 27~49 51~61 67~71 Export Carton Layer：3 Layers

Carton Size：350x350x290mm Width 16 24 32 44 Pcs／Reel 5K/1 5K/1 5K/1 5K/1 ? Reels／Carton 9/7/6/5/

Product Name: FPC

7 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2

10.操作指示Instruction upon usage 步骤 1:

Joining step 1： 使用拇指或食指，将上盖往上掀开。

Use the thumb or the forefinger, raise the top cover up.

步骤 2:

Joining step 2：

FPC 导电处朝下，平行的插入连接器中。 FPC gets along with conductivly down. The parallel one inserts it in the connector .

步骤 3:

Joining step 3：

轻压上盖中间往下旋转至定位，直到 FPC 完全 插入且没有移动。

Press the top cover lightly and rotate down to make a reservation , until FPC is totally inserted and not moved .

步骤 4:

Joining step 4：

FPC removal FPC 退出 小心掀起上盖，将 FPC 退出.

Lift the top cover carefully, withdraw FPC from .

警告 Warning!!

旋转的角度不可大于 135 度。

The whirling angle can't be greater than 135 degrees.

Product Name: FPC

8 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2

警告

Warning!!

当 FPC 插入的角度偏斜时，可能会引起导通不良。 When the angle that FPC inserts in is askew, may cause and lead openly and badly .

警告 Warning!!

当 FPC 插入的角度偏斜时，可能会引起导通不良。 When the angle that FPC inserts in is askew, may cause and lead openly and badly .

警告 Warning!!

向上拉扯的力量不要超过 0.05N/pin max.

The strength of dragging upwards don't exceed 0.05N/pin max .

警告 Warning!! 开启连接器掀盖时，不要使用过度的 力量及避免接触到端子。

covering , don't use excessive strength and avoid touching the end son .

警告 Warning!!

当在开启 FPC 时，不要使用过度的力量及避免接 触到端子。

Don't use excessive strength and avoid touching the end son when open FPC.

Product Name: FPC

9 of 10

ChinaTyco

FPC组

FPC Connector 0.3mmPitch Product Specification Issued Date2010-10-2

警告

Warning!!

施压的力量，应该要平均.

The strength of exerting pressure should be average.

如图所示，不要试着做移动或重新确定盖子位置。 As illustrated, do not attempt removal or re-positioning of the actuator.

警告 Warning!!

掀盖的面积，应该要平均.

Lift the area overlayed, should be average. 如图所示,

不要试着做移动或重新确定盖子的位置。 As illustrated, do not attempt removal or re-positioning of the actuator.

警告 Warning!!

PCB 板平整度必须在 0.1mm max.

The roughness of PCB board must be in 0.1mm max.

10 of 10

Product Name: FPC